Locating the product code of your weemote TV Remote

To locate your product code, unscrew the battery door from the back of your weemote. Next, remove the battery door and turn it completely around so the inside part of the battery door lid faces you. Note that this is the part of the lid that faces the batteries when it is secured to the weemote case. Now look at the white battery sticker and at the bottom of the battery door which contains your product code information.

If you don’t see any product code information at all, and front of your weemote has the Philips logo on it, then that model is considered an R5 version.

Valid product codes are R2 to R13B.

Entering Favorite Channels 1-5 (R10 and later)

To enter favorite channels 1-5

  1. Press and hold down the “C” button until the light turns on solid green, then release the “C” button
  2. Press and release the large #1 Favorite Button. The light should blink once.
  3. Enter the favorite channel as follows.
    3a. To enter thousands, use the “A” button
    3b. To enter hundreds, use the “100” button
    3c. To enter ones, use the “1” button
    3a. To enter a dash signal, use the “B” button. Dashes are used for sub-channels like channel 10-3, 14.5, etc.
  4. In this example, we will use channel 108.
    4a. Press and release the “100” button one time
    4b. Do not press the “10” button – this equals “0” for the ten value
    4c. Press and release the “1” button eight times
  5. Go back and press and release large #1 Favorite Button. This locks in the favorite channel on button 1.
  6. To continue with other favorites, Press and release the next Favorite Button to be programmed, in this case, button #2. The light should blink once. Then follow steps 3-5 again. Then back to step 2 for favorite channels 3,4 and 5.
  7. When done, press and release the “C” button to exit the program mode.

Learning the “Dash” Signal R10 and later

Here are some detailed instructions on how to learn the “Dash” signal as covered on Page 13 of the weemote® X Setup Guide

  1. Press and hold down the “B” button until the light turns on solid green, then release the “B” button.
  2. Press and release the small number “1” button in the program area at the bottom of the weemote®. The light should blink once.
  3. Press and release the large number “1” favorite button on the main part of the weemote®. The light should blink and then stay on orange.
  4. Point the 2 remotes towards each other with about a 2″ spacing. Also make sure the lens of each remote are in a line of sight to each other. Some remotes when placed on a surface have the lens slightly pointing up so you may need to lift the back portion of the existing remote to compensate.
  5. Press and release the “Dash” button on your existing remote. The weemote® LED light should blink twice orange and then go back on solid orange.
  6. . Press and release the “Dash” button on your existing remote for the second time. The weemote® LED light should blink three times orange and then go back on solid green to verify that learning is complete.
  7. Press and release the “B” button to exit programming mode. The weemote® LED light should blink three times green and then go completely out to confirm you have exited the program mode.

Note: If in Steps 6 and 7 the LED light happens to go RED, then this indicates there was an error learning. You will need to repeat pressing the button on the existing remote to resume learning. If this does work, exit program mode (Step 7) and repeat the steps but this time check the lighting, spacing and alignment between the remotes. You may need to try different spacing like 1″ apart instead or 2″ for example.

How to learn a signal on one of the Favorite Buttons

The following step-by-step example illustrates how to learn the “Guide” button from your Satellite Remote.

To learn the Guide button from the Shaw remote to the Favorite #1 button on the weemote® X. The same procedure can be used to learn any other signals on to the Favorite buttons #2-#5.

  1. Press and hold down the “B” button until the light turns on solid green, then release the “B” button
  2. Press and release the “100” button in the program area, the light will change from green to orange
  3. Press and release the Favorite #1″ button. The light will blink orange
  4. When starting the learning process, please make sure to review the information on page 5 of the weemote® X reference guide for helpful tips. Generally, there should be about 2″ of space between the remote’s and they should be pointing at each other straight. If you don’t get the proper response in steps 5-6, you might need to move the remotes closer together.
  5. Press and release the “Guide” button from the Shaw Remote. After about .5 second delay, the weemote® X light should blink orange twice and then go back on solid orange.
  6. Press and release the “Guide” button from the Shaw Remote for the second time. After about .5 second delay, the weemote® X light should blink orange three times and then go back on solid green.
  7. Press and release the “B” button to exit program mode. The weemote® X light should blink three times and then go out.